Chimney Services West Deerfield IL

We are your one stop West Deerfield chimney shop!

  • We eliminate the guesswork. And provide our customers cutting edge West Deerfield chimney repair technology.
  • We are clean.  And ensure our footwear never touches your floors. Our industrial vacuums collect the dust before it gets into your home while our trained technician sweeps and inspects the chimney flue.
  • You are safe!  We document every job with before and after photos, and the lead technician on the job is always certified.  We also test for excess levels of carbon monoxide at no additional cost to you. Our West Deerfield company is about making your home safe.

We begin with a West Deerfield chimney inspection—which is one of the most important chimney services we offer, and one of the most misunderstood. The inspection determines the status of your chimney. We have created a page where specifics are listed.  We are CSIA certified.

Does Your Chimney Need to Be Repaired?

Chimney Crown Crack

The most common cause of chimney related roof leaks is the chimney flashing. In fact, if you have a roof leak in the vicinity of the chimney, it is most likely the flashing. Chimney flashing is a 6 to 8 inch metal strip (usually lead or aluminum) used to seal the transition joint between the shingles and the chimney.

In some cases the chimney flashing was never installed, installed improperly or over time has deteriorated. Seasonal heating and cooling can cause flashing joints to break and open the water tight seal. The "old technology" method of repairing chimney flashing used a tar based material over the suspected leaking areas.

Unfortunately, the tar material for flashing repair is only a short term patch. All tar based chimney flashing patching compounds are not UV stable, and over time they degrade and crack on the roof. This either opens the old leaking areas or allows new leaks to form.

Sometimes a chimney sweep Chicago just isn’t enough. Over time your chimney and fireplace can become worn and damaged due to weathering and moisture. Regular chimney maintenance is suggested to avoid costly repairs down the line. Often a chimney can be restored with some basic repair such as sealing, spot tuck-pointing or minor brick replacement. It is important to address water damage and flaking bricks early on. If your chimney is not properly maintained and cared for then more severe repairs may be required.

What Causes Chimneys to Develop Cracks?

Chimney Restoration

In many cases the damage of a chimney is so substantial that tuckpointing will not work. When this happens a chimney, and/or fireplace, rebuild is necessary. As a result of direct exposure to all aspects of weather (especially freeze-thaw cycles), the mortar that keeps the bricks held together will crack, allowing water entry. The brickwork is porous and becomes saturated. This creates the framework of the brick to degrade, which causes a safety concern for the chimney and for your home.

A chimney is probably one of the most ignored and poorly maintained structures on a home mainly because of lack of access and most people have a fear of heights.

Things to watch for if your chimney is having problems is crumbling mortar joints, cracked or broken brick, a cracked or missing crown on top of the chimney, a leaning chimney(which is really bad) and water damage inside your home around the chimney. You should contact a chimney repair or mason contractor to fix your chimney problems.

But if you are up to the challenge here is what you will need to do, first depending on how bad it is most chimney problems can be fixed with a little chimney tuckpointing. You will first need a good grinder, not a cheap $20 on either, buy a dewalt or hitatchi for about $120.00 then you will also need a good diamond 4 inch wheel to go on it, they will run you about $65.00.

Start by grinding out every mortar joint as deep as you can get the blade in, be sure to wear safety glasses and a mask if not you will regret it later. After all the joints have been ground out take your brush and clean out all the joints thoroughly. Now you will need to mix your mortar, after it is mixed it is easiest to use a grout bag to fill the joints, which resembles a large cake decorating bag if you dont know what one is. Be sure you mix is fluid enough to flow through bag but not too wet where it has no body or else you will have a huge mess on your hands. Depending on temperature you have to check your joints frequently to see if they are ready to be struck with a striking iron or a rake.

After you have struck or raked your joints brush them down to remove loose mortar and clean up the chimney. Next check the concrete cap, if it is cracked then it should be replaced and a new one should be poured in its place that is alteast 4 inches thick. After that task is completed check the chimney flashing and be sure it is installed correctly and is hole and crack free or it may need to be caulked up or replaced. Then clean up your roof with a broom or hose but if using water try not to spray your chimney till its dry.

That's pretty much how a brick tuckpointing job is done for an existing chimney, if you are unsure of any of the above task you really should have a mason contractor do the work for you.


Illinois Chimney Services

Home