Chimney Services Sylvan Lake IL

We are your one stop Sylvan Lake chimney shop!

  • We eliminate the guesswork. And provide our customers cutting edge Sylvan Lake chimney repair technology.
  • We are clean.  And ensure our footwear never touches your floors. Our industrial vacuums collect the dust before it gets into your home while our trained technician sweeps and inspects the chimney flue.
  • You are safe!  We document every job with before and after photos, and the lead technician on the job is always certified.  We also test for excess levels of carbon monoxide at no additional cost to you. Our Sylvan Lake company is about making your home safe.

We begin with a Sylvan Lake chimney inspection—which is one of the most important chimney services we offer, and one of the most misunderstood. The inspection determines the status of your chimney. We have created a page where specifics are listed.  We are CSIA certified.

Reasons to Reline Your Chimney

Chimney Company

The first step to determining if the flashing is the cause of the leak is to examine the chimney. The weakest points of the chimney are the top and sides. These are the areas that face the greatest UV and weather exposure, and therefore damage. Since is better protected, you will notice the side facing the ground does not have flashing. Inspect the base area for cracks or areas of water penetration.

The brick and mortar will expand and contract with seasonal change. Since the mortar is not elastomeric, this expansion and contraction can cause cracks. In addition, mortar is very porous and absorbs water that will freeze in cold climates. This freezing and thawing will destroy the mortar joint causing a potential leak and degrading the structural integrity of the chimney over time. Inspect the mortar joints for cracks.

If there are cracks in the chimney use a clear exterior elastomeric caulk to seal the cracks. You can also use an exterior masonary waterproofing sealant to coat the entire chimney. Be sure to use a clear elastomeric waterproofing sealant to maintain the color of the brick and mortar.

When is a Chimney Repair Not Enough?

How To Make Chimney Crown

A chimney is probably one of the most ignored and poorly maintained structures on a home mainly because of lack of access and most people have a fear of heights.

Things to watch for if your chimney is having problems is crumbling mortar joints, cracked or broken brick, a cracked or missing crown on top of the chimney, a leaning chimney(which is really bad) and water damage inside your home around the chimney. You should contact a chimney repair or mason contractor to fix your chimney problems.

But if you are up to the challenge here is what you will need to do, first depending on how bad it is most chimney problems can be fixed with a little chimney tuckpointing. You will first need a good grinder, not a cheap $20 on either, buy a dewalt or hitatchi for about $120.00 then you will also need a good diamond 4 inch wheel to go on it, they will run you about $65.00.

Start by grinding out every mortar joint as deep as you can get the blade in, be sure to wear safety glasses and a mask if not you will regret it later. After all the joints have been ground out take your brush and clean out all the joints thoroughly. Now you will need to mix your mortar, after it is mixed it is easiest to use a grout bag to fill the joints, which resembles a large cake decorating bag if you dont know what one is. Be sure you mix is fluid enough to flow through bag but not too wet where it has no body or else you will have a huge mess on your hands. Depending on temperature you have to check your joints frequently to see if they are ready to be struck with a striking iron or a rake.

After you have struck or raked your joints brush them down to remove loose mortar and clean up the chimney. Next check the concrete cap, if it is cracked then it should be replaced and a new one should be poured in its place that is alteast 4 inches thick. After that task is completed check the chimney flashing and be sure it is installed correctly and is hole and crack free or it may need to be caulked up or replaced. Then clean up your roof with a broom or hose but if using water try not to spray your chimney till its dry.

That's pretty much how a brick tuckpointing job is done for an existing chimney, if you are unsure of any of the above task you really should have a mason contractor do the work for you.

Finally, if the chimney is constantly used and the required repairs are not done, the fire can possibly break out to other parts of your home. This is a life-threatening danger, and that is why chimney repair needs to be carried out occasionally.

If your home is old but the chimney is recent, think about the investment in getting your chimney repaired so as to safeguard your home. If you can perform any of the chimney repair work by yourself, you can bring down the expenses by working by yourself.

A total renovation of your chimney can be costly and in some cases going for up to hundreds of dollars. In some cases the cost can go up to thousands of dollars depending on the range of the work required and who you employ to perform the task.

If you want to hire the contractor to do a cleaning job as well, you can simply include that to the entire amount of your invoice.

Although you prefer to go about getting the work done, bear in mind that it will most likely in the long run cost you more if problems go without being dealt with due to the dangers in your house and since getting a chimney fully replaced is all the more costly.


Illinois Chimney Services

Home