Chimney Services Zion IL

We are your one stop Zion chimney shop!

  • We eliminate the guesswork. And provide our customers cutting edge Zion chimney repair technology.
  • We are clean.  And ensure our footwear never touches your floors. Our industrial vacuums collect the dust before it gets into your home while our trained technician sweeps and inspects the chimney flue.
  • You are safe!  We document every job with before and after photos, and the lead technician on the job is always certified.  We also test for excess levels of carbon monoxide at no additional cost to you. Our Zion company is about making your home safe.

We begin with a Zion chimney inspection—which is one of the most important chimney services we offer, and one of the most misunderstood. The inspection determines the status of your chimney. We have created a page where specifics are listed.  We are CSIA certified.

When is a Chimney Repair Not Enough?

Chimney Inspector

The first step to determining if the flashing is the cause of the leak is to examine the chimney. The weakest points of the chimney are the top and sides. These are the areas that face the greatest UV and weather exposure, and therefore damage. Since is better protected, you will notice the side facing the ground does not have flashing. Inspect the base area for cracks or areas of water penetration.

The brick and mortar will expand and contract with seasonal change. Since the mortar is not elastomeric, this expansion and contraction can cause cracks. In addition, mortar is very porous and absorbs water that will freeze in cold climates. This freezing and thawing will destroy the mortar joint causing a potential leak and degrading the structural integrity of the chimney over time. Inspect the mortar joints for cracks.

If there are cracks in the chimney use a clear exterior elastomeric caulk to seal the cracks. You can also use an exterior masonary waterproofing sealant to coat the entire chimney. Be sure to use a clear elastomeric waterproofing sealant to maintain the color of the brick and mortar.

Our Chimney Sweep and Cleaning Services

Chimney Cleaning Near Me

Steps

1. Before starting working on a chimney, make certain that the fire has long burned out.

2. The first thing you need to do is to measure the interior diameter of the metal or prefabricated chimney by removing the chimney cap with measuring tape. In case you have masonry chimney design, gauge the length and width of the flue liner. Take a moderate length chimney brush according to the calculated measures. The brush should neither be too small nor too large.

3. Stiff bristled brush and rods are ideal for chimney cleaning. These are easily available at any hardware stores.

4. To prevent ash or soot escaping into the room, use duct tape or masking tape to attach the cloth or sheet to the fireplace opening.

5. Change your clothes and climb up to the roof top. Don't forget to keep your chimney rods, flashlight and brush with you before climbing on the roof. Wear goggles and breathing mask as well.

6. If your chimney contains cap, remove it and clean it with the brush.

7. Attach few rods with brush and put it inside the chimney. Keep adding rods until you feel that the brush is touching the damper assembly.

8. Now you are ready to clean the flue. Move brush in up and down direction and scrape it against the walls of the chimney. Remove all the creosote (in form of ash, soot or as black shiny hardened gaze or a black crunchy substance).

9. Clean the whole length of the chimney in the same way. Afterwards take a flashlight and examine the chimney for any signs of creosote.

10. If you find chimney clean from the top side, come down and proceed to clean the chimney from inside the home. Remove the sheet or cloth you attach before. Keep a drop cloth on the site where your will have to work. Clean the damper assembly and the side walls of the chimney with brush. Examine any remaining of the creosote with flashlight.

11. Now clean the surrounding of the fireplace with vacuum or simply sweep it with broom. Remove the drop cloth carefully. Now is the time to rub your equipment clean from creosote. Remove your goggles and breathing mask. Place the equipment at its storage place for future cleaning.

12. Don't forget to inspect your chimney for any damage signs while cleaning process. If you find any, consult professionals.

13. If mortar is loose or damage, clear it and apply new mortar on the surface. Cracks can also be filled with mortar. It is recommended to use weather resistant mortar to give long life to your chimney.

14. Inspect the flashing seals for any damage. Use caulk to prevent any leakage, especially at the joints between chimney and flashing.

Precautions

- Always use breathing mask and eye safety goggles while working on chimney.
- Be careful about the surroundings while working on the roof top.


Illinois Chimney Services

Home