We are your one stop Barrington Hills chimney shop!

  • We eliminate the guesswork. And provide our customers cutting edge Barrington Hills chimney repair technology.
  • We are clean.  And ensure our footwear never touches your floors. Our industrial vacuums collect the dust before it gets into your home while our trained technician sweeps and inspects the chimney flue.
  • You are safe!  We document every job with before and after photos, and the lead technician on the job is always certified.  We also test for excess levels of carbon monoxide at no additional cost to you. Our Barrington Hills company is about making your home safe.

We begin with a Barrington Hills chimney inspection—which is one of the most important chimney services we offer, and one of the most misunderstood. The inspection determines the status of your chimney. We have created a page where specifics are listed.  We are CSIA certified.

Chimney Repair Expenses - A Brief Guide

Chimney Contractors Near Me

Repairing Chimney Flashing Easily

Once you have completed the inspection of the chimney, take a look at the flashing and shingles around the chimney. If the shingles around the chimney are cracked or have holes then repairing the chimney flashing area is easily accomplished by sealing the shingles and the chimney flashing with an elastomeric roof coating. If you do not want unsightly black patches on your roof use a clear elastomeric roof coating designed for asphalt shingles.

Before applying the elastomeric roof coating, fill the cracks and holes with clear exterior elastomeric caulk. Next, following the manufactures instructions apply the elastomeric roof coating.

Although the best time for repairing chimney flashing is in warmer weather, some elastomeric roof coatings and caulk can be applied in below freezing and even on a damp roof surface.

The first step to determining if the flashing is the cause of the leak is to examine the chimney. The weakest points of the chimney are the top and sides. These are the areas that face the greatest UV and weather exposure, and therefore damage. Since is better protected, you will notice the side facing the ground does not have flashing. Inspect the base area for cracks or areas of water penetration.

The brick and mortar will expand and contract with seasonal change. Since the mortar is not elastomeric, this expansion and contraction can cause cracks. In addition, mortar is very porous and absorbs water that will freeze in cold climates. This freezing and thawing will destroy the mortar joint causing a potential leak and degrading the structural integrity of the chimney over time. Inspect the mortar joints for cracks.

If there are cracks in the chimney use a clear exterior elastomeric caulk to seal the cracks. You can also use an exterior masonary waterproofing sealant to coat the entire chimney. Be sure to use a clear elastomeric waterproofing sealant to maintain the color of the brick and mortar.

What you may not understand is the chimney affects the entire foundation of your house. After all, your house is built around your fireplace, so if there is a serious issue with your chimney, you may be dealing with much more than a simple repair. Chimney cracks and unsightly damage may be a sign of a much larger problem in your home, so it's important to address any and all types of mortar repairs before they become a potentially disastrous situation. If your chimney is not working properly, you may not even know it. To this end, it is very dangerous to use before having it inspected for any and all necessary repairs. Since the weather is turning colder, make major repairs to your chimney before winter sets in and stay both warm and safe.

Types of Chimney Rebuilds

How To Do Chimney Crown

Your chimney isn't properly protected. Making sure that your top plate and rain cap remain in good condition, to prevent moisture from running into the chimney. Rodents, tree limbs and severe weather can all damage these.

Another option to prevent moisture and acid buildup from putting such heavy wear-and-tear on your chimney are chimney flue liners. These products range from smooth wall liners that prevent moisture and acid from attaching to interior chimney walls at all to simple protective devices that catch that residue.

The bottom line: No matter what kind of chimney you have, regular inspections can help give you peace of mind. Visually inspect exterior walls, bricks and mortar for signs of cracking. Use your fingers to see if mortar remains firmly in place, or chunks away. For interior chimney inspections, consider a using an inspection mirror with a telescopic handle. Coupled with a flashlight, the mirror will help you conduct a visual inspection and spot any signs of cracking.


Illinois Chimney Services

Home

We are your one stop Barrington Hills chimney shop!

  • We eliminate the guesswork. And provide our customers cutting edge Barrington Hills chimney repair technology.
  • We are clean.  And ensure our footwear never touches your floors. Our industrial vacuums collect the dust before it gets into your home while our trained technician sweeps and inspects the chimney flue.
  • You are safe!  We document every job with before and after photos, and the lead technician on the job is always certified.  We also test for excess levels of carbon monoxide at no additional cost to you. Our Barrington Hills company is about making your home safe.

We begin with a Barrington Hills chimney inspection—which is one of the most important chimney services we offer, and one of the most misunderstood. The inspection determines the status of your chimney. We have created a page where specifics are listed.  We are CSIA certified.

When selecting your next chimney sweep look for these five qualifications

Chimney Crown Cap

Steps

1. Before starting working on a chimney, make certain that the fire has long burned out.

2. The first thing you need to do is to measure the interior diameter of the metal or prefabricated chimney by removing the chimney cap with measuring tape. In case you have masonry chimney design, gauge the length and width of the flue liner. Take a moderate length chimney brush according to the calculated measures. The brush should neither be too small nor too large.

3. Stiff bristled brush and rods are ideal for chimney cleaning. These are easily available at any hardware stores.

4. To prevent ash or soot escaping into the room, use duct tape or masking tape to attach the cloth or sheet to the fireplace opening.

5. Change your clothes and climb up to the roof top. Don't forget to keep your chimney rods, flashlight and brush with you before climbing on the roof. Wear goggles and breathing mask as well.

6. If your chimney contains cap, remove it and clean it with the brush.

7. Attach few rods with brush and put it inside the chimney. Keep adding rods until you feel that the brush is touching the damper assembly.

8. Now you are ready to clean the flue. Move brush in up and down direction and scrape it against the walls of the chimney. Remove all the creosote (in form of ash, soot or as black shiny hardened gaze or a black crunchy substance).

9. Clean the whole length of the chimney in the same way. Afterwards take a flashlight and examine the chimney for any signs of creosote.

10. If you find chimney clean from the top side, come down and proceed to clean the chimney from inside the home. Remove the sheet or cloth you attach before. Keep a drop cloth on the site where your will have to work. Clean the damper assembly and the side walls of the chimney with brush. Examine any remaining of the creosote with flashlight.

11. Now clean the surrounding of the fireplace with vacuum or simply sweep it with broom. Remove the drop cloth carefully. Now is the time to rub your equipment clean from creosote. Remove your goggles and breathing mask. Place the equipment at its storage place for future cleaning.

12. Don't forget to inspect your chimney for any damage signs while cleaning process. If you find any, consult professionals.

13. If mortar is loose or damage, clear it and apply new mortar on the surface. Cracks can also be filled with mortar. It is recommended to use weather resistant mortar to give long life to your chimney.

14. Inspect the flashing seals for any damage. Use caulk to prevent any leakage, especially at the joints between chimney and flashing.

Precautions

- Always use breathing mask and eye safety goggles while working on chimney.
- Be careful about the surroundings while working on the roof top.

Steps

1. Before starting working on a chimney, make certain that the fire has long burned out.

2. The first thing you need to do is to measure the interior diameter of the metal or prefabricated chimney by removing the chimney cap with measuring tape. In case you have masonry chimney design, gauge the length and width of the flue liner. Take a moderate length chimney brush according to the calculated measures. The brush should neither be too small nor too large.

3. Stiff bristled brush and rods are ideal for chimney cleaning. These are easily available at any hardware stores.

4. To prevent ash or soot escaping into the room, use duct tape or masking tape to attach the cloth or sheet to the fireplace opening.

5. Change your clothes and climb up to the roof top. Don't forget to keep your chimney rods, flashlight and brush with you before climbing on the roof. Wear goggles and breathing mask as well.

6. If your chimney contains cap, remove it and clean it with the brush.

7. Attach few rods with brush and put it inside the chimney. Keep adding rods until you feel that the brush is touching the damper assembly.

8. Now you are ready to clean the flue. Move brush in up and down direction and scrape it against the walls of the chimney. Remove all the creosote (in form of ash, soot or as black shiny hardened gaze or a black crunchy substance).

9. Clean the whole length of the chimney in the same way. Afterwards take a flashlight and examine the chimney for any signs of creosote.

10. If you find chimney clean from the top side, come down and proceed to clean the chimney from inside the home. Remove the sheet or cloth you attach before. Keep a drop cloth on the site where your will have to work. Clean the damper assembly and the side walls of the chimney with brush. Examine any remaining of the creosote with flashlight.

11. Now clean the surrounding of the fireplace with vacuum or simply sweep it with broom. Remove the drop cloth carefully. Now is the time to rub your equipment clean from creosote. Remove your goggles and breathing mask. Place the equipment at its storage place for future cleaning.

12. Don't forget to inspect your chimney for any damage signs while cleaning process. If you find any, consult professionals.

13. If mortar is loose or damage, clear it and apply new mortar on the surface. Cracks can also be filled with mortar. It is recommended to use weather resistant mortar to give long life to your chimney.

14. Inspect the flashing seals for any damage. Use caulk to prevent any leakage, especially at the joints between chimney and flashing.

Precautions

- Always use breathing mask and eye safety goggles while working on chimney.
- Be careful about the surroundings while working on the roof top.

Caps: Chimney caps keep water and animals out of your flue. Both can cause major damage and prevent your chimney from drawing correctly, so it's important to have a cap installed. We highly recommend screened caps to keep birds, bats, and other animals out.

If your fireplace is damaged, it's also important to have it repaired immediately. While many fireplace repair issues are simply aesthetic, you don't want to take any chances! Structural and other safety risks are possible with a damaged fireplace, so be sure your chimney professional inspects and repairs your fireplace as well as your chimney.

For safe fireplace function, have an annual fireplace and chimney inspection. By following through with all recommended repairs, you can rest easy knowing that your fireplace and chimney pose no danger to your home or your family!

All About Chimney Repairs and Concrete Restoration

Chimney Crown Repair

Repairing Chimney Flashing Easily

Once you have completed the inspection of the chimney, take a look at the flashing and shingles around the chimney. If the shingles around the chimney are cracked or have holes then repairing the chimney flashing area is easily accomplished by sealing the shingles and the chimney flashing with an elastomeric roof coating. If you do not want unsightly black patches on your roof use a clear elastomeric roof coating designed for asphalt shingles.

Before applying the elastomeric roof coating, fill the cracks and holes with clear exterior elastomeric caulk. Next, following the manufactures instructions apply the elastomeric roof coating.

Although the best time for repairing chimney flashing is in warmer weather, some elastomeric roof coatings and caulk can be applied in below freezing and even on a damp roof surface.


Illinois Chimney Services

Home